How To Mix Stucco Base Coat (2024)

The Three Methods of how to mix stucco base coat

There are three primary methods for how to mix stucco, each with its unique advantages and disadvantages. The choice will depend on personal preference and the scope of your project.

How to mix stucco with a bucket, paddle, and drill

The bucket-and-drill method is a common choice for smaller projects. This involves pouring the stucco mix into a clean bucket (usually a 5 gallon bucket) and using a paddle attached to a drill to mix until a smooth texture is achieved. This is a simple method for how to mix stucco base coat when dealing with smaller quantities. This stucco mixing method is also more common for less expereinced contractors and can be more cost effective for smaller projects.

How to mix stucco with a wheelbarrow and shovel

If you're dealing with a slightly larger project, the wheelbarrow and hoe/shovel mixing method may be more appropriate. Begin by adding the stucco mixture to the wheelbarrow and use the hoe or shovel to mix. This method allows for larger quantities of mixing stucco (typically when more than five gallons of stucco are needed). The downside of this stucco mixing method is that a lot more manual work is required, which means for larger residential type jobs you’ll be better off with a barrel or mortar mixer

How to mix stucco with a mortar mixer

For a more advanced solution on mixing stucco, contractors typically use a mortar mixer.These mixers are efficient and designed for large-scale projects (like residential jobs), ensuring a consistent stucco mix every time. There is much less manual work that is required when mixing the stucco - add yourcementitious material such as EIFS, plaster, or stucco and the mixer does the rest.

Regardless of the stucco mixing method you choose, always follow the manufacturer's instructions and safety guidelines for best results when you mix stucco base coat.

Stucco Mix Ratio forcementitious materials

Correct stucco mix ratios are important for a successful and long-lasting finish. The right mix of sand, cement, and water ensure the stucco has a proper consistency and adhesion to the substrate.

Usually a stucco base coat has a stucco mix ratio of 3 parts sand, 1 part cement, and enough water to achieve the desired consistency. But, these ratios may vary based on the project requirements or the manufacturer's recommendations.

mixing stucco base coat for pumping

When preparing to pump stucco basecoats, the right mix can make all the difference. Fiber reinforced cement basecoat consists of an 80 pound (lb.) bag of concentrated cement mixed with 200-240 lbs. of washed sand certified to American Society for Testing and Materials (ASTM) standard C897 or C144, and potable water.

Many manufacturers offer proprietary “pump grade” mixes which contain a greater proportion of lime, a workability agent added to mortar mixes. These proprietary mixes are ideal for providing better pumpability and better product on the wall, and are highly recommended if available. Manufacturers do not always have pump grade mixes available, though, so field mixes are sometimes needed. To help ensure smooth pumping and avoid pack-outs, follow these guidelines to prepare the mix.

Tips to keep in mind when mixing stucco for pumping:

  1. Using the right sand.Be sure to start with sand that meets the appropriate ASTM gradations. If rocks over ¼ inch (in.) in diameter are present, whether from the incorrect grade of sand or because the delivery truck was not cleared of debris before loading the sand, the material may pack-out in the pump, delivery hose or application nozzle.
  2. Getting the mix right.Many pumps will not efficiently move mortars that approach or exceed the recommended amount of sand. Pump pack-outs usually start when the mix contains too much sand or there is not enough water in the mix. The key to adding the correct amount of sand is to start at 75 percent of the recommended sand for the mix, and then slowly increase as-needed. Water content in mixing mortar is also important for creating a mix that is workable for both pumpability and wall applications. When starting operationsfor the day, mix the material slightly wetter than normal for the first batch and then gradually add more sand to subsequent batches until the recommended limit is reached or the pump no longer moves efficiently. If the pump packs out while slowly increasing sand, you’ll know how much sand is too much for future batches. In case of a pack-out while mixing, reduce the amount of sand and increase water to richen the mix and try to pump any suspect material out of the hose before resuming pumping operations. Adding a few handfuls of lime to the mix will also help improve the workability and pumpability of the mortar.
  3. Optimize pumpability throughout the day. Once the optimal amount of sand for ideal pumpability has been reached, it is important to stay consistent throughout the day. Keep an eye on your mix throughout the day and be prepared to add/reduce sand or water to keep the mix consistent as you pump.
  4. Preparing the pump. Before you can start pumping for the day, the hose must be completely wetted out. Ideally, run a slurry of lime and water through the hose to lubricate it before pumping begins. If lime is not available, use water alone. If you try to pump before wetting out the hose, the dry hose will absorb the water from the mix and pack-out immediately. Once the hose has been wetted out, pump the mortar through the hose until it reaches the end. Install the application nozzle and then adjust the pump speed/air ratio to obtain a consistent spray pattern. Just as you must wet the hose before pumping, it is important to clean the hose right after pumping is completed for the day.If not cleaned quickly, the cement will dry in the hose, rendering it unusable.

In addition to preparing the mix and pump properly, consider the diameter and layout of the hose. The larger the diameter of the pump hose, the less work the pump has to do. Avoid using a hose smaller than 1 ¼ in. when pumping field mixes. Ideally, start with a 1 ½ in. hose with a 1 ¼ in. section for the nozzle.

If you have excess hose on your job site, avoid laying the hose in loops, as they create a significant amount of back pressure and can create kinks in the hose as it is pulled while the pump is running. Instead, lay the hose on the ground in an S-pattern to keep the mortar moving.

If a pump grade mix is not available for your job, adhering to these guidelines when mixing your basecoat in the field will help get the job done faster and with fewer stops.

Benefits of using a Graco mortar mixer

Using a Graco mortar mixer when mixing stucco base coat offers several benefits:

1. Consistent Results and Increased Productivity: Graco mortar mixers make sure each stucco base coat batch is mixed thoroughly and consistently. This mixing consistency leads to better results and saves time by reducing manual mixing.

2. User-friendly Operation: Graco mortar mixers feature simple controls - making it easier for contractors learning how to mix cement for stucco, and for experienced contractors to reduce maintenance.

3. Portability: Graco mortar mixers are designed for easy mobility around a jobsite, improving efficiency and flexibility for mixing stucco.

4. Easy to Clean and Transport: Graco mortar mixers can be easily disassembled for thorough cleaning and efficient transport.

Using a Graco mortar mixer can streamline your stucco mixing process and help with consistent results and boosting productivity. Check out our ToughTek mortar mixers and piston pumps below for your next stucco project.

How To Mix Stucco Base Coat (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Melvina Ondricka

Last Updated:

Views: 6317

Rating: 4.8 / 5 (48 voted)

Reviews: 95% of readers found this page helpful

Author information

Name: Melvina Ondricka

Birthday: 2000-12-23

Address: Suite 382 139 Shaniqua Locks, Paulaborough, UT 90498

Phone: +636383657021

Job: Dynamic Government Specialist

Hobby: Kite flying, Watching movies, Knitting, Model building, Reading, Wood carving, Paintball

Introduction: My name is Melvina Ondricka, I am a helpful, fancy, friendly, innocent, outstanding, courageous, thoughtful person who loves writing and wants to share my knowledge and understanding with you.